Instructions
BC HWID Spoofer setup guide
BC HWID Spoofer • HWID Spoofer
Launching BC HWID SPOOFER: the spoofer changes your hardware IDs so you can play again after a hardware ban.
Instructions
The spoofer changes your hardware data so you can play after a hardware ban. First set up the BIOS and change your disk serial numbers, then run the loader from a USB flash drive and choose HWID Spoofer and the [pay] version. To undo the spoof, just restart your PC as usual.
Preparing BIOS and Windows
1. The BIOS must be set to AHCI. Almost all new PCs already have it, but check. If it is set to IDE, you need to change it to AHCI (this usually requires a full Windows reinstall).
2. Disable the security module TPM in the BIOS (it may be called Trusted Platform Module, TPM Device, Security Chip, fTPM or PTT). If your board has no such module, you don't need to do anything.
3. In the BIOS, this mode must be enabled: Fast Boot.
4. Before using the spoofer, it is strongly recommended to reinstall Windows, restart your router (if it has a dynamic IP), delete the old game folder and install the game again.
5. Special note for Rust and EFT: the anti-cheats of these games update very often, and the spoofer sometimes stops working for them temporarily. Check the status with support before launching: https://t.me/CheatForce_support_bot. Other games have no official support, but the spoofer will most likely work for them too.
2. Disable the security module TPM in the BIOS (it may be called Trusted Platform Module, TPM Device, Security Chip, fTPM or PTT). If your board has no such module, you don't need to do anything.
3. In the BIOS, this mode must be enabled: Fast Boot.
4. Before using the spoofer, it is strongly recommended to reinstall Windows, restart your router (if it has a dynamic IP), delete the old game folder and install the game again.
5. Special note for Rust and EFT: the anti-cheats of these games update very often, and the spoofer sometimes stops working for them temporarily. Check the status with support before launching: https://t.me/CheatForce_support_bot. Other games have no official support, but the spoofer will most likely work for them too.
Running the spoofer
1. Ideally, keep the loader on removable media (for example, a USB flash drive) and remove it before starting the game. For the EAC version, the loader must be run strictly from a flash drive, or you will get an injection error.
2. Download the loader: download. Archive password: 123.
3. Download the program for changing disk serial numbers: download. Run it, change the value in the "Serial Number" field for each of your disks and restart your PC. Make sure TPM is disabled.
4. Run the loader and select HWID Spoofer.
5. Choose the version marked [pay] and click LAUNCH.
6. Wait for the loader to close. After that you can start the game. If you want to play with a cheat, start the cheat first, then the game.
7. Versions marked Static change the data once, and it stays the same on every injection. To reset it, delete the "hwid" file from the loader folder and restart your PC.
2. Download the loader: download. Archive password: 123.
3. Download the program for changing disk serial numbers: download. Run it, change the value in the "Serial Number" field for each of your disks and restart your PC. Make sure TPM is disabled.
4. Run the loader and select HWID Spoofer.
5. Choose the version marked [pay] and click LAUNCH.
6. Wait for the loader to close. After that you can start the game. If you want to play with a cheat, start the cheat first, then the game.
7. Versions marked Static change the data once, and it stays the same on every injection. To reset it, delete the "hwid" file from the loader folder and restart your PC.
How to check that the spoofer worked
1. After injection you will hear a short beep: if you heard it, everything is fine. If not, some of the recommendations were not followed, and you need to check all the steps again.
2. An extra check: before running the spoofer, enter the command WMIC DISKDRIVE GET SERIALNUMBER in the console, then repeat it after running the spoofer. If the data differs, the spoofer works; if not, recheck all the steps.
3. To undo the spoofer, just restart your PC.
2. An extra check: before running the spoofer, enter the command WMIC DISKDRIVE GET SERIALNUMBER in the console, then repeat it after running the spoofer. If the data differs, the spoofer works; if not, recheck all the steps.
3. To undo the spoofer, just restart your PC.